Accessories
Stud Bolts
Standards: ASTM, ASME, API, BS, DIN, AFNOR, JIS, UNI, SIS, GOST Chrome, Moly, Aluminum, Duplex, Alloy steel, Inconel, Nickel Alloys, Hastelloys, Titanium
Grades: A193, A194, A320 B7, B7M, 2H, 2HM, L7, L7M, 7, 4, B8, B8M, 8, 8M, B16 NACE MR‐ 01‐75
Types: Stud Bolts, Anchor Bolts, Turbine Bolting, High Tensile Threaded Rods, Hex Head Bolt, Cap Screws, Nuts, & Washers.
Threading: ISO System‐Triangular proof thread, Symmetric Trapezoidal, thread, ISO Pipe Thread. ASA System‐UNC Triangular Profile thread (Standard Services), UNF Triangular Profile Thread (Special Series), NPT Conical Thread with Triangular Profile ACME Trapezoidal profile thread.
Coatings: Cadmium , Galvanized, PTFE, XYLAN
Gaskets
Materials: Soft Iron, Stainless Steel, Carbon Steel, Monel, Nickel Alloys, Incoloy, Titanium, Duplex.
Grade: SS304, SS316, F11, F22, 904L, UNS 8825
Types: Spiral Wound, Sheet gasket, Ring Joint, Gasket, Metal Jacketed.
Spiral Type: CGI, CG
RTJ Type: Oval, Octagonal
Sheet Type: Raised Face, Full Face Metal Jacketed
Type: Single, Double
Sizes: ½” to 56”
Class: 150 to 2500
Filler: Graphite, Non-Asbestos, PTFE, Asbestos
Insulation Kit
Materials: Gasket –Reinforced Phenolic, Neoprene faced Sleeve‐ Polyethylene, Phenolic, Mylar, Minlon, Nomex, CAF. Washer – Carbon Steel, Phenolic.
Types: RF, Full Face, RTJ
Sizes: ½” TO 24”
Class: 150 to 2500
Sheets
Sizes: 1.5m x 1.5m, 2m x 1.5m Thickness: 1mm to 3m
Materials: Asbestos, Non‐ Asbestos, Graphite, Rubber.
Steam Traps
Materials: Cast Iron, Stainless Steel, Caron Steel, Alloy Steel
Sizes: ½” to 2”
Types: Thermostatic, Mechanical, Thermodynamic, Drain Orifice
Pressure: up to 600 PSI
Ends: NPT, BSPT, Flanged RF
Strainers
Materials: Cast Iron, Ductile Iron, Bronze, Carbon Steel, Low Temp Steel, Chrome Molly, Stainless Steel, Other materials on request.
Sizes: ½” to 24”
Types: Y‐ Type, Basket, T‐Type, Temporary Strainers
Class: 150 to 2500# Mesh : 40, 80, Non Standard mesh available on request
Ends: Flat Face, Raised Face, RTJ, Buttweld, Threaded (NPT), Socket Weld.
Pressure Regulators
Material: Cast Iron, Carbon Steel
Sizes: 3/8” to 12”
Types: Direct Acting / Pilot Regulated
Pressure: up to 600 PSI
Ends: Flanged, Threaded (NPT)
Standards: ASTM, ASME, API, BS, DIN, AFNOR, JIS, UNI, SIS, GOST Chrome, Moly, Aluminum, Duplex, Alloy steel, Inconel, Nickel Alloys, Hastelloys, Titanium
Grades: A193, A194, A320 B7, B7M, 2H, 2HM, L7, L7M, 7, 4, B8, B8M, 8, 8M, B16 NACE MR‐ 01‐75
Types: Stud Bolts, Anchor Bolts, Turbine Bolting, High Tensile Threaded Rods, Hex Head Bolt, Cap Screws, Nuts, & Washers.
Threading: ISO System‐Triangular proof thread, Symmetric Trapezoidal, thread, ISO Pipe Thread. ASA System‐UNC Triangular Profile thread (Standard Services), UNF Triangular Profile Thread (Special Series), NPT Conical Thread with Triangular Profile ACME Trapezoidal profile thread.
Coatings: Cadmium , Galvanized, PTFE, XYLAN
Gaskets
Materials: Soft Iron, Stainless Steel, Carbon Steel, Monel, Nickel Alloys, Incoloy, Titanium, Duplex.
Grade: SS304, SS316, F11, F22, 904L, UNS 8825
Types: Spiral Wound, Sheet gasket, Ring Joint, Gasket, Metal Jacketed.
Spiral Type: CGI, CG
RTJ Type: Oval, Octagonal
Sheet Type: Raised Face, Full Face Metal Jacketed
Type: Single, Double
Sizes: ½” to 56”
Class: 150 to 2500
Filler: Graphite, Non-Asbestos, PTFE, Asbestos
Insulation Kit
Materials: Gasket –Reinforced Phenolic, Neoprene faced Sleeve‐ Polyethylene, Phenolic, Mylar, Minlon, Nomex, CAF. Washer – Carbon Steel, Phenolic.
Types: RF, Full Face, RTJ
Sizes: ½” TO 24”
Class: 150 to 2500
Sheets
Sizes: 1.5m x 1.5m, 2m x 1.5m Thickness: 1mm to 3m
Materials: Asbestos, Non‐ Asbestos, Graphite, Rubber.
Steam Traps
Materials: Cast Iron, Stainless Steel, Caron Steel, Alloy Steel
Sizes: ½” to 2”
Types: Thermostatic, Mechanical, Thermodynamic, Drain Orifice
Pressure: up to 600 PSI
Ends: NPT, BSPT, Flanged RF
Strainers
Materials: Cast Iron, Ductile Iron, Bronze, Carbon Steel, Low Temp Steel, Chrome Molly, Stainless Steel, Other materials on request.
Sizes: ½” to 24”
Types: Y‐ Type, Basket, T‐Type, Temporary Strainers
Class: 150 to 2500# Mesh : 40, 80, Non Standard mesh available on request
Ends: Flat Face, Raised Face, RTJ, Buttweld, Threaded (NPT), Socket Weld.
Pressure Regulators
Material: Cast Iron, Carbon Steel
Sizes: 3/8” to 12”
Types: Direct Acting / Pilot Regulated
Pressure: up to 600 PSI
Ends: Flanged, Threaded (NPT)
